The timer is now programmed. “ON” will ash for 5 seconds
and then stop. The timer screen will go blank after 5 minutes to
conserve power. The time and program status, “ON” or “OFF,” will
remain visible. Pressing any button will “wake” the timer.
Move back to ZONE and select the unprogrammed zone. Repeat
the programming steps to set-up the second watering zone.
Changing the Program
To make a change to the program, simply wake the timer by
pressing any button. Move to the sections you wish to change and
adjust as needed. Watering will resume at the “START WATER” time.
Manual Watering
Using the UP and DOWN arrows, move to “MANUAL.” Using the
PLUS button, adjust the time you wish to water. The timer will wait
5 seconds and begin to water. Manual watering can be up to 240
minutes.
Rain Delay
In the event of predicted rainfall, you can temporarily suspend
automatic watering for up to 3 days. Simply move to “RAIN DELAY”
and use the PLUS button to select the desired delay. After the
delay period has passed the timer will return to the programmed
operation.
Automatic Rain Delay
This timer will work with AquaSentry, Melnor’s exclusive Automatic
Rain Delay. AquaSentry actually monitors the moisture in the soil
and delays watering if it is not needed. For more information, visit:
www.melnor.com/conservation/aqua-sentry.html.
Disabling the Program
If you would like to suspend automatic watering for an extended
period, simply change the “PROGRAM” line to “OFF.” When you are
ready to resume watering, switch “PROGRAM” to “ON.” Watering
will begin at the “START WATER” time. Each “ZONE” is disabled or
enabled independently.
Program Memory
This timer has memory. If the battery fails or is removed, even for
extended periods, the program will be retained. After installing
a fresh battery you simply need to set the “TIME.” The timer will
retain the existing program.
Batteries
Install 2 AA Alkaline batteries by removing the battery holder
from the back of the timer and inserting the batteries as indicated.
Replace the battery holder.
Once installed, the LCD screen will be working with the letters
“OFF” ashing beside “MANUAL.”
Installing the Timer
Attach the timer directly to an outside faucet and turn on the
water.
Attach a hose to the timer outlet and then to a sprinkler, soaker
hose or other watering system.
Note: The timer can be programmed before installation.
Programming the Timer
Press the UP key until the numbers beside “TIME” are ashing.
UP
MINUS PLUS
DOWN
Set the current time using the PLUS and MINUS keys. By holding
the key down the time will change rapidly. A tap will cause a
stepped change. Once you have set the correct time, use the
DOWN arrow key to move to the next section.
Use the PLUS and MINUS keys to select the “ZONE” you want
to program. Use the DOWN key to move to the next section.
Select when you want to begin watering in the “START WATER”
section. Again adjust the time using the PLUS and MINUS keys.
Move to the next section.
Set how long you wish the water to run in the “WATER FOR”
section. This time can be adjusted up to 240 minutes. Move to the
next section.
Select how often you would like to water in the “WATER EVERY”
section. This is set in hours or days. Move to the next section.
Activate the program by adjusting the “PROGRAM” section to
ON. Watering will begin at the “START WATER” time.
Melnor, Inc. • Winchester, Virginia 22603, USA
877-283-0697 • www.melnor.com
3100_INS_EN_WEB
3100
Two-zone Electronic Water Timer
User Instructions
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals